|
|
|
Who's Online
There currently are 5935 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
;
It was just what I need to fix my old BMW's CD player. Very convenient also. Thank you.
;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
;
Great manual very clear copied. You are making an incredible job. I appreciate a lot the rapidity and your efficiency. Thanks a lot
O
High Voltage Regulation Adjustment
Digital Multi-Meter(DMM)
4) HS (Horizontal Shift) Adjust so that the horizontal center line of a digital circle pattern is in accord with geometric horizontal center of the CPT. 5) EW (East-west Width) Adjust until the outermost left and right vertical line of the screen is accord with the edge of the frame. 6) EP (East-west Parabolar) Adjust so that middle portion of the outermost left and right vertical line looks like parallel with vertical lines of the CPT. 7) ET(East-west Trapezium) Adjust to make the length of top horizontal line same with it of the bottom horizontal line. 8) A-ANG(AFC Angle) 9) A-BOW(AFC BOW) 10) U-C(Upper Cotner Pincushion) 11) L-C(Lower Cotner Pincushion) 12) U-VL(Upper Vertical Linearity) 13) L-VL(Lower Vertical Linearity) 14) VL (Vertical Linearity) Adjust so that the boundary line between upper and lower half is in accord with geometric horizontal center of the CPT. 15) SC (Vertical �S� Correction) Adjust so that all distance between each horizontal lines are to be the same. 16) V-ASP(Vertical Aspect Ratio) Adjust the vertical aspect ratio.
1. Test Equipment 2. Preliminary steps
1) Switch picture mode to STANDARD in no signal input.
3. Adjustment
1) Connect �+� terminal(Red) of DMM to the Anode of D432 and �-� terminal(Black) to the Heat Sink of Q406. 2) Adjust VR401 so that the D432 terminal voltage is 21.3!0.1V.
O
CUT-OFF Adjustment
1) Press the �SVC� button and then press the � � button on the remote controller for adjustment to display horizontal
line.(Even though you enter into the SVC mode, the horizontal line might not be seen according to the position of Screen Volume.) 2) Adjust Screen Volume (R/G/B) in Focus Pack until brightness of red/blue/green horizontal line is about not to be seen.(At this moment, brightness of red, blue or green horizontal line should be equal to one another.) 3) Exit the adjustment mode by pressing the � � button.
O
Deflection Adjustment
1) Adjust differently based on input signal such as NTSC or PAL. 2) NTSC adjustment should be done in STANDARD mode of picture after receving 13CH signal,and PAL adjustment should be done in STANDARD mode of picture after receving EU05 CH. 3) Reset the data in convergence adjustment mode,quit the mode. Convergence Mode : SVC, M Data reset : 5 , OK Adjustment mode out :
M
1. Preliminary steps
17) Store the adjusted data in EEPROM by pressing the �OK� button before exiting adjustment mode. 18) Restore the convergence correction data by pressing the �TV/AV� button before exiting adjustment mode
2. PAL Mode Deflection Adjustment
1) At SVC mode,press the YELLOW key get into the deflection adjustment mode. 2) VS (Vertical Shift) Adjust until geometric vertical certer line of the screen is accord with the vertical center line of the screen JIG at EU 05 CH by pressing the VOLUME F ,G button. 3) VA (Vertical Amplitude) Adjust until fifth vertical line from upper and lower center of the screen is accord with the edge of the frame.
3. NTSC Mode Deflection Adjustment
1) Adjust vertical size (VA Adjustment) until fourth vertical bar from upper and lower center screen is accord with the edge of the frame. 2) Adjust horizontal size (EW Adjustment) until third bar to indicate horizontal size of circle is accord with the edge of the frame. 3) Do other adjustments the same as in PAL mode.
Fourth Vertical Line
Third Bar
Fifth Vertical Line
Outmost Vertical Line
- 12 -
|
|
|
> |
|
